WireX3000 Series Terminal
The WireTerminals in the X3000 series produce fully automatically terminated wires for control cabinet wiring. Up to 36 different wires can be processed without the need for changeovers. The wire cross-sections range from 0.5 mm² to 6 mm².
The standard equipment of the WireThe X3000 series terminal can be connected to a wide range of optional processing stations can be expanded to meet your requirements flexibly.
In the case of wire end ferrules crimped at both ends or ultrasonic compaction, simultaneous processing of the wire ends can result in a Cycle time of 3 seconds can be achieved.
Standard equipment
3-way shuttle system
Simultaneous end machining
The wires are transported via a linear shuttle system comprising three independently operating shuttles. Each shuttle ensures precise and rapid wire movement.
The shuttle system allows both ends of the wire to be processed simultaneously, thereby significantly reducing the cycle time per wire.
Wire feed casette
36 wires at the same time
The WireThe X3000 series terminal can handle up to 36 wires simultaneously with a cross-sectional area of 0.5 to 6 mm² can be processed. The wires can be processed one after the other without the need for changeovers. The integrated wire straightening station straightens the wire immediately as it enters the machine.
To process different types of wire, you simply need to replace one of the three wire feed cassettes. The changeover is quick and requires no tools, thanks to a quick-change system.
Each wire feed cassette is uniquely identified by a built-in RFID chip. Reading the chip identifies which wires are on the WireTerminals are equipped.
Wire feed cassettes with an integrated display, which synchronises with production in real time, are available as an option. This allows you to see the current production status of the wire feed cassette at a glance.
All fine-stranded copper wires conforming to DIN VDE 0295 Class 5 can be processed.
Stripping station
Stripping of all cross-sections
The use of two V-blades enables the precise stripping of wires of all compatible cross-sections without the need to change tools.
A stepless full extension of 2 to 20 mm is possible, as well as a sContinuously adjustable partial retraction from 6 to 20 mm.
Depending on the dispensing points
Output handling
The finished wires can be dispensed by dropping, into wire guides, into wire chains or into wire chains grouped together to form bundles.
Provided that the processing station for the wire rails in the WireIf it is integrated into the terminal, output is handled by a SCARA axis system. If this is not the case, output is handled using an alternative method.
Optional processing stations
Wire marking station
The wires are marked using inkjet printing, either in black or white.
Up to two built-in printers enable uninterrupted alternating operation without any waiting times.
Text can be applied in precise positions or in a continuous pattern, ensuring clear identification.
Heat-shrink tubing station
Each wire is marked with up to two printed heat-shrink sleeves.
Inkjet printing can be carried out in two lines for tube lengths of 9 to 35 mm.
Secure fastening is achieved in conjunction with the subsequent crimping of wire end ferrules or the pressing on of cable lugs.
Wire end ferrule crimping station
Loose wire end ferrules ranging from 0.5 to 6 mm² are processed using two in-house developed 16+4-station crimpers with a ServoquattriX SW press. The customisable oscillating feeders offer you maximum flexibility.
Ultrasonic Compaction Station
The in-house developed station uses ultrasound to crimp stripped wire ends ranging from 6 to 16 mm with precision and reliability.
The sonotrode has a cross-shaped design, which has the advantage that previously unused compaction surfaces can be utilised by rotating the unit during servicing.
Quadruple servo press station
The in-house developed processing station can be fitted with up to four insulated, belt-mounted contacts at the same time. The WireThe terminal can be fitted with red, blue and yellow contacts in any combination.
Ultra-short-wire station
This processing station reduces the minimum wire length to 90 mm. All other processing stations can be used in combination with the ultra-short-wire station.
Output in WireRails
The wires are placed individually and loosely in the cable trays without any adhesive tape. In doing so, the WireEach terminal can be fitted with up to 15 wire rails.
Each cross-section is sorted by type and placed in its own wire tray in accordance with the specified wiring sequence.
Output in tape chains
When arranged in wire chains, the wires are secured one behind the other using two adhesive tapes, in accordance with the wiring sequence.
All wires can be laid down regardless of their end finish and cross-section.
wire chain bundler
The finished wire chains are each tied into a handy bundle using a printed label before being dispensed.
This prevents the individual wire chains from becoming tangled and makes it easier to sort the wires as they are dispensed.
Technical data
| WireTerminal X3000 Series | |
| Number of wires processed simultaneously | 36 |
| Wire length range | 240 mm to 7,000 mm |
| with ultra-short-wire station | from 90 mm |
| Heat-shrink tubing length | 9 mm to 35 mm |
| Wire cross-sections | 0.5 mm2 up to 6 mm2 |
| Wire diameter | min. 1.6 mm, max. 5,5 mm |
| Stepless partial extraction | 6 mm to 20 mm |
| Stepless full trigger | 2 mm to 20 mm |
| Number of wire end ferrules processed simultaneously | 16+4 |
| Ferrule length | 8 mm to 18 mm |
| Length range of the ultrasonic compaction station | 6 mm to 16 mm |
| Number of insulated, strapped contacts fitted simultaneously | 4 (red, blue, yellow – can be combined as desired) |
| Cycle time for machining both ends | from 3 seconds. |
| Dimensions | Length = 4,350 mm Width = 2,200 mm (2,950 mm) Height = 2,020 mm |
| Weight | approx. 3,800 kg |
| Compressed air connection | min. 6 bar, max. 10 bar |
| Compressed air consumption | 80 Nl/min to 160 Nl/min |
| Sound pressure level | 73 dB(A) |
| Operating voltage | 3×400 V + N, 50 Hz |
| Control voltage | 24 V |
| Power consumption (approx.) | 3 kW |